Feedburner Facebook youtube pinterest twitter

Tuesday, October 20, 2015

Unroot and Unbrick LG G Pad V410 AT&T Tablet back to stock

Again, my curious mind had to fiddle with another Android device causing a hard brick.  After seeing here on the AT&T website that Lollipop was out for the LG G pad v410, figured could easily bring the tablet back to stock using this firmware found on XDA.  Very bad move, after flashing the firmware using TWRP for the LG-v410, went into settings on the tablet, and did a software update. This caused the tablet to reboot back into TWRP recovery.  Next going back to XDA, where I originally downloaded the stock zip file, flashed the stock recovery for the LG-v410.  Whoops, now the tablet was, as they call it, hard bricked, now the tablet was stuck on a boot loop showing only the LG Logo.

Anyways, found the LG mobile update tool, the online one did not seem to want to work, so I came across the LG Flash Tool 2014.  Only problem was, could only find firmware for newer or older models.  Forums and other blogs will say that you can flash the V40010c.kdz, this may work if you did not totally brick your tablet and can still get into recovery, although, if you did what I had done, the drivers are not going to correctly install while in download mode.  They may while in TWRP recovery, since you can enable MTP in TWRP recovery.

After much searching, did finally find the KDZ file for the AT&T LG-v410, if you already know what to do, you can grab it right here:

LG G Pad V410(7.0) KDZ AT&T LG Mobile Tool


  1. Make sure your tablet is powered off, if stuck in the LG logo boot loop, hold the volume+ and power button until the tablet powers completely off.
  2. Now while holding just the volume+ button, at the same time plug the tablet into the USB cable to the PC
You should now get this screen:

LG-v410 Download mode
Now grab the LG Flash Tool 2014 along with the correct driver here, this is for offline flashing:


Now that you have everything you need, follow this link and unbrick or simply bring your LG G Pad 7.0 back to factory stock!  The directions are for the LG G2, but the same procedure works for the LG G Pad v410.
Posted by at
Labels: ,

8 comments :

  1. UnknownJanuary 7, 2016 at 1:30 PM

    Hey, thanks for this! When I finished updating, it booted with AT&T logo but is asking for pin/password to decrypt. Any idea about that?

    ReplyDelete
  2. AnonymousFebruary 2, 2016 at 12:09 AM

    Yes. Same Thing happened to me. Boot into the so called "factory reset mode".
    1) Power off
    2) Hold Down Volume Down
    3) Press and hold power while still holding volume down.
    4) Wait for LG screen.
    5) While still holding volume down, release and immediately repress and hold down power.
    6) Go through on screen steps to reset device.

    It will take a long time to boot, but when it does it will go through the regular initial device setup.

    Hope this helps.

    ReplyDelete
  3. unlock centerJuly 15, 2016 at 6:59 PM

    ready al 100

    ReplyDelete
  4. yasirAugust 29, 2016 at 3:03 PM

    hi dear i flash that rom my tab was 16gb now it is showing aroung 4gb any help please

    ReplyDelete
  5. UnknownSeptember 7, 2016 at 5:13 PM

    a mi me paso lo mismo mi tablet era de 16 gb y ahora me marca de 8gb

    ReplyDelete
  6. UnknownSeptember 7, 2016 at 5:13 PM

    a mi me paso lo mismo mi tablet era de 16 gb y ahora me marca de 8gb

    ReplyDelete
  7. kenedy cruzFebruary 7, 2018 at 1:01 PM

    quien tenga la version 41010d.KDZ esa es la version de 16gb quien la tenga me la pasa

    ReplyDelete

Subscribe to: Post Comments ( Atom )

Adsense

My Blog List